I have an Overhead door opener model # XXXXX I need to find out how to program my wall remote on my garage door. (My son's old girl friend has the current code and I want to erase it from the unit's memory and reset it with a new code.) There are three buttons on the back of the motor unit. I think they read from left to right: SW3, SW2 & SW 1.
- Brand Name: Overhead Door. Model Number: 55B, 1/3 HP. It works fine and comes with everything needed for easy operation. I am guessing this operator is from 1980 - before the sensors were a requirement. It was in use with a 16 x 7 insulated garage door with windows. I replaced it because it only has one remote, and I had an opportunity to.
- Our NSCD-360OV1 360MHz compatible remote is the perfect remote to replace your old and defective remote. North Shore Commercial Door decided to manufacture this remote to fill the need for a high quality yet inexpensive OHD 360 remote. The remote features excellent range and reliability. Features - 9 dip switches - 360 frequency - long lasting battery model# 9V - Visor Clip - Excellent.
Programming your Overhead Door Codedodger® wireless keypad. Should you need additional information please contact our customer service department at 1-800-275-6187.
Resetting your keypad:
If, at any time, during programming, you should enter the wrong PIN or make a mistake, you should reset the keypad to its factory setting.
Open the keypad cover half way
Press and hold the number 8 and the PROG buttons while opening cover fully.
The indicator light will blink once and go out.
Close the cover. You are now ready to re-program your keypad.
Basic Programming:
Open cover fully - Indicator will blink once on go out
Press 3-5-7
Press PROG - Indicator will blink once per second
Enter PIN 1 (up to 8 digits)
Press PROG - Indicator will blink twice per second
Close cover. Your keypad is now ready to be programmed to the garage door opener.
Locate the Learn code button on your Codedodger garage door opener.
Depending on model, the learn code button will be located under the light cover or on the rear panel.
Basic Opener Programming:
Press the learn code button - Learn code LED will flash
Open cover on keypad fully
Enter PIN number
Press the SEND button 4 times, or until the door begins to operate.
You will now be able to use your wireless keypad normally.
Controlling a single door with your keypad:
Open keypad fully
Press PIN number
Press SEND once
Door should operate normally
Note: As a “panic” feature this keypad will operate door for up to 30 seconds from any button.
Programming multiple doors with your keypad:
Program your keypad according to the steps outlined in the Basic programming section listed above.
Open cover fully
Enter PIN number
Press PROG - Indicator will blink once per second
Press PROG - Indicator will blink twice per second
Press PROG - Indicator will blink three times per second
Enter the total number of doors (2 or 3)
Press PROG
Close cover
Your keypad is now ready to be program to the garage door openers.
Locate the learn code button on your garage door openers
Press the learn code button once - Learn code indicator will flash
Open cover on keypad fully
Enter PIN
Press SEND
Enter door number 1-2-or-3
Press send button 4 times, or until door operates
Repeat these steps for door 2 and 3
Controlling multiple doors:
Open cover fully
Enter PIN number
Press SEND
Enter door number (1-2-or 3)
Chosen door should operate
Adding PIN 2:
Open cover fully
Enter 1-5-9
Press PROG - Indicator will blink once per second
Enter PIN 2 (up to 8 digits)
Press PROG Indicator will go out
Close cover. Your keypad is now ready to be programmed to the garage door opener.
See steps in Basic programming.
Adding temporary PIN:
Open cover fully
Enter PIN 1
Press PROG - Indicator will blink once per second
Press PROG - Indicator will blink twice per second
Enter temporary PIN
Press PROG - Indicator will blink three times per second
Close cover. Your keypad is now ready to be programmed to the garage door opener.
See steps in Basic programming.
Canceling the temporary PIN:
The temporary PIN will remain active until PIN 1 is entered.
Changing a PIN:
Open cover fully
Enter PIN to be changed
Press PROG Indicator will blink once per second
Enter new PIN
Press PROG
Indicator will blink twice if PIN 1 has changed or go out if PIN 2 was changed
Close cover. Your keypad is now ready to be programmed to the garage door opener.
Locate the Learn code button on your Codedodger garage door opener.
Depending on model, the learn code button will be located under the light cover or on the rear panel.
Our polystyrene insulated garage door model 391 has a 9.8 R-value for a more comfortable garage and a steel backing for security and a finished appearance. A lifetime limited warranty on these steel garage doors means it is built to last. A wide variety of standard and premium window options are also available for these steel garage doors.
Warranty
Lifetime LimitedEmbossed wood grain texture
Adds beauty, sophistication and durability
Steel Backing
For strength, finished interior appearance
Galvanized steel center stiles
For maximum strength and weight
Durable Finish
Hot-dipped galvanized steel with two coats of baked-on polyester paint
Bulb-type bottom weather seal
Guards against wind and rain while providing cushion when closing
Standard Panel
Insulation
Polystyrene insulation with an R-value of 9.8 for improved energy efficiency and sound reduction
Overhead Door Model 55b Remote Keyless
Doors are available in five standard colors or can be painted to match your home’s décor.
Clear Short
Cascade 1
Madison 1
Sherwood 1
Stockford 1
Waterton 1
Williamsburg 1 (4 pc.)
Ashton 1
Cathedral 1
Ruston 1
Stockton 1
Winston 1
Williamsburg 1 (8 pc.) Double Wide Doors Only
Overhead Door Model 551 Programming
Traditional Steel Collection Brochure
Traditional Steel Warranty (390 Series)